OPERATIONAL REQUIREMENTS
VACUUM-----20-25



DIRECTORY ASSIGNING

  JOB DATABASE DIRECTORY: C:\JOBS
  USE CATEGORIES: DISABLE

  JOB DATABASE DIRECTORY : A:\
  USE CATEGORIES: ENABLE

CONFIG: BP-2200/240/ASM80PQR AFS JM LPT2





PROBLEMS ENCOUNTERED

PROBLEM: PICKS UP AT NO SITE
SOL'N: STOP HANDLER PRESS AT HHT [GOTO][RUNSTEP][2][9][ENTER]


ALIGNMENT OF HEAD/EDITING AT HHT TO ALIGN HEAD PLACEMENT OR PICK-UP

...[FUNCTION][3][ENTER]
...[PLACE][TYPE IN NUMBER OF SITE TO BE MODIFIED][ENTER]
...[ENTER]
...SAMPLE WINDOW WILL APPEAR X:11111:[TYPE IN IF WANT TO MODIFY][ENTER]
                             Y ALL IN MILS
                             T
                             Z  

BP1200 AT IPS

                         1(CONNECTION)
                        []PARALLEL PORT         ---------------------------                                 
                        |                       |                         | 
                        |                       |        IPS              |
         __________________                     |        -----------      |
         |                |                     |     1  |         |      |
         |                |                     |  [][]  |         |      |
         |    TROLEY      |                     |--------           -------
         |     CART       |
         |                |
         ------------------
                        2(CONNECTION RIBBON CABLE)

                                        ---------
                                        |        | 
                                       2|BP 1200 |3      LOADBOARD(3)
                                        |--------











PASSWORD FOR BP PROGRAMMER
    >MICE - AT POWER UP
    >



IMPORTANT POINTS ON BP PROGRAMMER
     1. CHECK PROGRAMMER IF ITS ON VERSION 3.47
         a. IF VERSION IS NOT THE SAME
         b. GO TO C DRIVE TYPE C:>CD\BP_47 
     2. Ist device to program should be good if not reload program then change device at ist unit of tray.

     3. AT POWER DOWN BP DEFAULTS TO ONLY SUBMENU AFTER AFS  BUFFER  DEVICE ..ETC
          > QUIT THEN GOTO CONFIGURE THEN CHOOSE FROM OPERATOR(BETWEEN MANUAL OR OPERATOR CHOICE)

     4. IF DEVICE NEEDS DISKETTE, AT POWER DOWN REMOVE DISKETTE.

     5. HAND HELD TERMINAL CONSOLE INITIALIZATION
          >X MOTOR
          >Y
          >T
          >LASTLY "V ENTER COMMAND" - THIS TIME YOU CAN PRESS RUN FOR PRODUCTION
     6. 

           











ENABLE SITES WITH BP LOADBOARD
     1. ESCAPE PROGRAM FROM PRODUCTION
     2. GOTO ENGG MENU BY PRESSING ESC
     3. YOU WILL BE ASK OF PASSWORD: UPPER CASE "STEP"
     4. PRESS ALT + D
     5. TO ADD A SITE, INSTALL LOADBOARD, THEN VISION TEACH-PRESS ENTER TO OPEN/ENTER TO GO DOWN
     6. TEST DIAGNOSTICS OF SITE ADDED IF PASSED THEN IT CAN GO FOR PRODUCTION ELSE REPLACE LOADBOARD.

TO REPLACE STEPPER MOTOR
     1. AT BP PROGRAMMER(A-SELECT)
     2. QUIT BP PROGRAMMER, OR GOTO DRIVE C
     3. THEN POWER OFF.
     4. REPLACE MOTOR

CONVERT FROM 80PIN TO 100PIN OR VISE VERSA
     1. POWER OFF PROGRAMMER


 BP PROGRAMMER BIOS VERSION UPGRADE
1. Make sure all sites are connected and the PC is interfaced with the programmer
2. Select BP DIAGNOSTICS MODE.
3. In DEVICE/OPTIONS make sure Master site is # 1.
4. Go to DEVICE/FLASH.
5. It will prompt you where is the file. Type in a:\118.bin
6. Screen will prompt you to type in UPGRADE. key this in.
7. It will automatically erase and re-program the BIOS.
8. It may or may not broadcast the data to the rest of the site.
9. After it is complete, it will show cycle system power to be powered off.
10. Turn off Programmer.
11. Then turn on Programmer again.
12. Follow steps 2 to 11 but this time the master site is #2 as you want to upgrade if it does not 
      broadcast to the rest of sites. 



At the window for BP Programmer
    Config: BP-1148 LPT1 Blank-Check Verify-Twice Check IDs
    Device: AMD Am27C512
    Buffer: f:\sw\latest\ATLATU.203  
1. Buffer 
      a. Load
2. Device
      a. program
3. Select
4. Select
5. Quit