Big update
Now Playing: Dr. Who on Netflix

Okay, so I have not been very diligent in updating. I've done bits here and there as time and funds would allow.

I have spent the past three years refurbishing peices of the car, including dash mounting peice, steering wheel mount, inside upper a-pillars, and many other bits. All of these I removed the rust and coated with Por-15.

I have also been learing how to weld, and that has been a big plus in the rebuild department.

1st (summer, 2009) I did get the engine to fire. It simply took a bit of starting fluid. I need to adjust the carbs yet, as I have rebuilt them since I last ran the engine, but at least I know it works. http://s209.photobucket.com/albums/bb266/byak0/engine/?action=view&current=EngRunning.flv

 2nd (ongoing throughout 2009), I have nearly completed the passenger side rebuild. I needed new floor crossmembers so I built some new ones, with the help of a friend who works at a sheet metal shop. He was able to bend new ones for me, out of 22 ga paint lock steel. I needed to weld in new inner supports.  http://s209.photobucket.com/albums/bb266/byak0/passfirewall/

http://s209.photobucket.com/albums/bb266/byak0/passenger%20side%20floorboard%20and%20rockers/

http://s209.photobucket.com/albums/bb266/byak0/Misc%20car%20parts/

http://s209.photobucket.com/albums/bb266/byak0/Floor%20Crossmembers/

I have a corner where the heel board and the inner rocker panel meet that needs to be re constructed, then I will be able to weld the rest of the passenger side together. I have reconstructed and refurbished the passenger side fire wall.

Items replaced or refurbished on the passenger side are as follows: complete floor pan, floor crossmember, rocker panel-all 3 parts, uppper and lower a-pillar (new lower, rebuilt upper) and the fire wall.

In my haste to weld the new components in I neglected to adjust the door first. In the end I discovered the door to be way out of adjustment. I had to slice a bit of the repaired firewall out to make adjustment room to bring the bottom of the door back into alignment. Word of warning. Check your fit before you weld.

3rd (mid 2009), I have started the drivers side rebuild. All components on this side have been replaced by new or refurbished parts from donor cars. No original metal was salvageable. http://s209.photobucket.com/albums/bb266/byak0/driver%20floor/http://s209.photobucket.com/albums/bb266/byak0/driver%20floor/

I also worked on modifying the alternator bracket (to lower the alt 2"-it was rubbing on the bonnet)http://s209.photobucket.com/albums/bb266/byak0/engine/

(summer 2009) I built a new lower a-pillar and floor crossmember.

(3-20-2010, 25, 26)The new upper a-pillar I purchased from rimmer brothers did not come with the door jam so a new one needed to be constructed. I have spent the last two weeks (three days really) building this part, and it is now ready to install. I painted the entire inside of this part with por-15. After welding the inside and the outside, a little bit more needs to be coated with por-15.

http://s209.photobucket.com/albums/bb266/byak0/Upper%20A%20pillar/

4th (3-27-10), I have started rebuilding the firewall shelf as the old one (yeah, you gessed it, rusted beyond salvaging). I am currently in the process of forming the raised rectangles the components are mounted to. http://s209.photobucket.com/albums/bb266/byak0/Firewall%20shelf%20build/

Yet to come, both quarter-panels and the rear lower valance, the emblem mounting portion of the rear, the front lower valance, and replacing the left and right sides of the bonnet.

ho hum update
Mood:  not sure
Now Playing: Edvard Greig-peer gynt, no wait. now it is Aerosmith-Livin' on the Edge
No luck on getting the engine to turn over. I havent tried lately, but back in the summer I gave it quite a few attempts. Not sure what I am doing wrong, but I think have narrowed it down to lack of fuel getting into the carbs. (it's a bit more complicated than merely filling the tank, but thanks for the thought.)

As for the parts, I have many more prepped with the Por-15. I have heard a lot of good stuff about it. I hope everyone is right or I have wasted a lot of time.
I have my A-pillars rebuilt and ready to reinstall as soon as I get some new lower A-pillars and clean up the inside of the firewall the A-pillar mounts to.

Engine
It's been over 10 years since I tore the car apart.
I'm hoping I'm not crazy for trying the following. My engine is intact, in that I have not torn it apart, aside from removing the manifolds and the radiator. I am in the process of getting ready to fire it up, just to make sure every is still kosher. I have rebuilt the carburetors since I took the car apart, but have not had the opportunity toi tune them I realize I probably did this backwards, but se la vi. Anyway, My next post should be of the results of my starting test. I got it to turn over, with the coil disconnected, so I don't think there will be a problem, since it made no alarming noises. I have turned it over by hand semi-regularly, and it has been mostly garaged.
Wish me luck

Progressing slowly
Although I have not made any entries lately, I have been working on the car.

I have rebuilt one of the A-pillars, completely rust free! I am working on the other one. I have it close to completion. I used the A-pillars from the '69 parts car I have. They were in much better shape. Minor rust, but mostly I just wanted to make sure the inside portions are coated with Por-15 so as to prevent rust inside in the futrure.

I have also started work on the front valane. Its is slightly dinged up, but one of the previous owners (p.o.) had welded extensions on to it. Unfortunately they left a small space on each end where only water could get to. You gessed it, more rust. I think I'll have this piece sand blasted to clean it up before I do anything more.

Other completed peices of note are:
Gas pedal, Brake and clutch pedal-both with brand new pivot pins (thanks to a friend with a metal lathe). Various small body parts, bumper and hood mounting brackets. I could go on, but you get the picture.
All of these peices are at least stripped of all paint and rust, and most of them are coated in Por-15.

Topic: body work
Not really a lot to report since my last post.
I Purchased some Por 15 and have been prepping and coating parts to my a-pillars.

I also painted my wiper motor gloss black. Looks much better.

removal of A-pillar
Finally finished removing the interior portion of the A-pillar today. Lot of spot welds to remove.
Too much rust in there for me.

Just look at this close up of the inside.

I'm sure glad I decided to change these out instead of just hoping there was little rust inside.
Although the replacements I have were taken from another car and they have a slight amount of rust, they have cleaned up nicely and will be a welcome sight in the car.

**
(Try the following at your own risk and with good ventilation)
Today I also started experimenting with Electrolytic Rust Removal. (I only wish I had a tub large enough to hold the car body). I took a 5 gallon bucket and filled it with water.

I made the water a basic solution by adding some baking soda. I used a scrap peice of metal for the cathode and atached a wire to it. I also attached a wire to a rusted part. In this case I used an extra gas pedal assembly I have which happens to be extra rusty. (Boy, I sure have a lot of that).

The rusted part and the cathode are suspended from a board into the solution. Be careful not to let the two touch. I clipped the Negative end of my battery charger to the wire on the part and positive end to the cathode.

At this point, all you need to do is add juice. If the battery charger and the solution are strong enough, you should see bubbles start rising out of the solution. Be care as this is hydrogen. When the bubbling stops, your rust should be gone.

-------

I don't think I have my solution strong enough, however. I'll need to get some PH+ for swimming pools to increase the strength of the solution. Either that, or my small battery charger just doesn't have the proper umph and I'll need a larger one.

Work continues
Been working on removing the inside A-pillar. My exisiting ones are completely rusted, but fortunately its just the inside portion. Drilling out all htose spot welds is kind of a pain.

I have also started thinking of how to do the interior.
Here is a drawing I worked up with a stip of walnut, matching the dash, at the top of the door.

Rev it up!
It's been a long time coming. Ive had the new battery tray for over 7 years (That's actually the last time I had any money to buy anything) and I finally removed the old one. The new sits in place just fine, but I still need to weld it in.

The old was was in worse shape than I remembered it being (shocked?). Its been since 97 that I parked the '6 for restoration. That was when I tore it completely apart. I've been through 3 moves since then and finally have the time and a bit more ambition.