Irwin 23 Specs.
IRWIN 23 SPECIFICATIONS (thanks Mike Monaha
LOA 23' 0"
LWL 18' 0"
Beam 8' 0"
Draft Board Up 2' 5"
Draft Board Down 5' 9"
Mast Height Above DWL 31' 6"
Designed Displacement 3200 lbs, 3800 lbs actual
Later boats were lighter with less fiberglass
Lead Ballast 1500 lbs
Headroom Main cabin 5' 2"
Sail Area 260 Sq Ft
Main sail 126 Sq Ft
Star main 230 Sq Ft
Genoa 192 Sq Ft
Jib sail 124 Sq Ft
Spinnaker 391 Sq Ft
I = 28.5, J = 9, P= 24.75, E = 10.25
Sleeps Four
Designer: Ted Irwin
Production from 1970 until 1976
Over 450 built
-----------------------------------------------
1970 Irwin 23 specs, original brochure
provided by Paul Schlitz:
SPECIFICATIONS
- LOA.........................23' 0
- LWL.........................18
- Beam........................ 8' 0
- Draft Board Up.............. 2' 5
- Draft Board Down............ 5' 9
- Mast Height Above DWL.......31' 6
- Displacement................3200 lbs
- Lead Ballast................1500 lbs
- Sail Area..................256 Sq Ft
- Headroom Main cabin ........5' 2
- Sleeps Four
Standard Equipment, Hull & Deck, Interior Galley & Head
- Highest quality resin based gel-coat finish
- High impact fiberglass hull and deck with molded in non-skid
- Boot top in wide range of colors
- Custom cast metal stemhead with integral bow chocks
- Forward and main companionway hatches of molded fiberglass
- Teak toe rails, drip molding, companionway dropboards, transom gate dropboard and all exterior trim
- Gate valve on thru hull sink fitting below waterline
- Specially designed spade rudder of molded fiberglass with stainless steel shaft
- Solid molded fiberglass centerboard housed completely below cabin sole.
- Unitized molded fiberglass interior, generous storage area under all berths, rope locker forward.
- Insulating and acoustical carpeting on all exposed fiberglass surfaces (interior)
- Molded fiberglass headliner throughout main and forward cabins
- Molded-in simulated plank cabin sole
- Genuine hand rubbed walnut interior trim
- Simulated walnut pressure laminate
- Walnut trimmed dinette table with pressure laminate top
- Four full length bunks, two fwd, two in main cabin
- Starboard berth in main cabin converts to dinette
- Four inch foam mattresses covered in expanded vinyl complete with zipper and a wide range of decorator colors
- Head platform to stbd
- Stainless steel galley sink with manual fresh water pump
- 25 gallon water tank
- Convenient removable ice chest
- four ports; two large windows main cabin, one Fixed port in head,one fixed port forward cabin
Spars and Rigging; Deck and Cockpit Fittings and Hardware
- Anodized aluminum mast and boom
- Stainless steel mast tangs, chainplates and bolts
- Spring-loaded roller reefing
- Aluminum spreaders
- Main and jib halyard cleats
- Stainless steel standing rigging
- Bronze turnbuckles
- Dacron main and jib sheets
- Mast stepped on cabin top
- Roomy self bailing cockpit
- Cleat in cockpit for mainsheet
- Three mooring cleats
- Two teak cleats on winch islands for working jib sheets
- fairleads for working jib
- Centerboard winch, with handle conveniently located in cockpit
- Mahogany Tiller
- Custom cast bronze tiller head
- Transom gate with teak dropboard for outboard motor
- *All hardware is Bronze, Aluminum or Stainless Steel