Model Rocketry Safety Code

1. Materials
   My model rocket will be made of lightweight materials such as paper, wood, rubber, and plastic suitable for the power used and the performance of my model rocket. I will not use any metal for the nose cone, body, or fins of a model rocket.

    

2. Motors/Engines
   I will use only commercially-made NAR certified model rocket engines in the manner recommended by the manufacturer. I will not alter the model rocket engine, its parts, or its ingredients in any way.

    

3. Recovery
   I will always use a recovery system in my model rocket that will return it safely to the ground so it may be flown again. I will use only flame-resistant recovery wadding if required.

    

4. Weight and Power Limits
   My model rocket will weigh no more than 1500 grams (53 oz.) at lift-off, and its rocket engines will produce no more than 320 Newton-seconds (4.45 Newtons equal 1.0 pound) of total impulse. My model rocket will weigh no more than the engine manufacturer’s recommended maximum lift-off weight for the engines used, or I will use engines recommended by the manufacturer for my model rocket.

    

5. Stability
   I will check the stability of my model rocket before its first flight, except when launching a model rocket of already proven stability.

    

6. Payloads
   Except for insects, my model rocket will never carry live animals or a payload that is intended to be flammable, explosive, or harmful.

    

7. Launch Site
   I will launch my model rocket outdoors in a cleared area, free of tall trees, power lines, buildings, and dry brush and grass. My launch site will be at least as large as that recommended in the following table.

    

   LAUNCH SITE DIMENSIONS Minimum Installed Total Impulse (Newton-seconds) Equivalent Engine Type Site Dimension (feet) (meters) 0.00 ­ 1.25 1/4A & 1/2A 50 15 1.26 ­ 2.50 A 100 30 2.51 ­ 5.00 B 200 60 5.01 ­ 10.00 C 400 120 10.01 ­ 20.00 D 500 150 20.01 ­ 40.00 E 1000 300 40.01 ­ 80.00 F 1000 300 80.01 ­ 160.00 G 1000 300 160.01 ­ 320.00 2Gs 1500 450

    

8. Launcher
   I will launch my model rocket from a stable launching device that provides rigid guidance until the model rocket has reached a speed adequate to ensure a safe flight path. To prevent accidental eye injury, I will always place the launcher so that the end of the rod is above eye level or I will cap the end of the launch rod when approaching it. I will cap or disassemble my launch rod when not in use and I will never store it in an upright position. My launcher will have a jet deflector device to prevent the engine exhaust from hitting the ground directly. I will always clear the area around my launch device of brown grass, dry weeds, and other easy-to-burn materials.

    

9. Ignition System
   The system I use to launch my model rocket will be remotely controlled and electrically operated. It will contain a launching switch that will return to “off” when released. The system will contain a removable safety interlock in series with the launch switch. All persons will remain at least 15 feet (5 meters) from the model rocket when I am igniting model rocket engines totalling 30 Newton-seconds or less of total impulse and at least 30 feet (9 meters) from the model rocket when I am igniting model rocket engines totalling more than 30 Newton-seconds of total impulse. I will use only electrical igniters recommended by the engine manufacturer that will ignite model rocket engine(s) within one second of actuation of the launching switch.

    

10. Launch Safety
    I will ensure that people in the launch area are aware of the pending model rocket launch and can see the model rocket’s liftoff before I begin my audible five-second countdown. I will not launch a model rocket using it as a weapon. If my model rocket suffers a misfire, I will not allow anyone to approach it or the launcher until I have made certain that the safety interlock has been removed or that the battery has been disconnected from the ignition system. I will wait one minute after a misfire before allowing anyone to approach the launcher.

     

11. Flying Conditions
    I will launch my model rocket only when the wind is less than 20 miles (30 kilometers) an hour. I will not launch my model rocket so it flies into clouds, near aircraft in flight, or in a manner that is hazardous to people or property.

     

12. Pre-Launch Test
    When conducting research activities with unproven model rocket designs or methods I will, when possible, determine the reliability of my model rocket by pre-launch tests. I will conduct the launching of an unproven design in complete isolation from persons not participating in the actual launching.

     

13. Launch Angle
    My launch device will be pointed within 30 degrees of vertical. I will never use model rocket engines to propel any device horizontally.

     

14. Recovery Hazards
    If a model rocket becomes entangled in a power line or other dangerous place, I will not attempt to retrieve it. As a member of the Estes Model Rocketry Program, I promise to faithfully follow all rules of safe conduct as established in the above code.

*This is the official Model Rocketry Safety Code of the National Association of Rocketry and the Model Rocket Manufacturers Association.

Important Note: “G” engines must be sold to and used by adults (18 and up) only.

To launch large model rockets weighing more than one lb. (453 g) but no more than 3.3 lbs. (1500 g) including propellant or rockets containing more than 4 oz. (113 g) but no more than 4.4 oz. (125 g) of propellant (net weight), you must notify and perhaps obtain authorization from the Federal Aviation Administration (FAA). Check your telephone directory for the FAA office nearest you or contact Estes Industries for further information.