Since this was a DIY project I had to figure
out what parts I needed and where to get them.
This took a while too and as the actual work
was done I found myself needing some new
pieces here and there to get the job done.
There's gonna be stuff I left out but you'll
get the idea. You can find many of these
parts from other sources too, I just listed from whom
I found my parts from.
Turbo Components:
JWT T-28 turbo, Nissan GTi-R manifold, , braided
steel dash 4 oil pickup line w/ -4AN fitting,
4 Infinity Q45 or '95 300ZXTT injectors (370cc) on SR20DE
rail, GReddy 300ZXTT intercooler,
& HKS P-flow intake. Purchased together used from
SE-R.net Classifieds .
$1100
Electrical:
JWT ECU w/ turbo program
Jim Wolf Tech.
$600
Westco Sealed Battery
Westco Batteries
$85
8" battery tie downs
Autozone
$3
Autometer boost/oil/press/water temp guages
Carparts.com
$80
Plastic paper tray (cut up to make 3 hole
guage panel) Office
Depot
$3
O2 sensor wire, spiral wire wrap, solder,
tape
Pep Boys
$10
Intake Piping:
2"id 4" radius 90 degree mandrel bend
JC Whitney
$7
2"id 45 degree mandrel bend
JC Whitney
$6
2"id 3"radius 6"/15" leg J-pipe
Summit Racing
$12
2"id 3' exhaust pipe
Pep Boys
$9
2"id offset radiator hose
Napa
$12
2"id radiator stick hose 2'
Napa
$20
2.5"id 90 degree mandrel bend (two)
JC Whitney
$21
2.5"id radiator stick hose 1'
Napa
$21
Silicone 2.75"id to 2"id reducer
Turbonetics
$20
3/16"id vacuum line (for wastegate) 3'
Pep Boys
$2
4 way vaccuum tee (WG & guage)
Pep Boys
$2
Vacuum plugs
Pep Boys
$2
1 3/8"id K&N Breather
Austin Performance $15
Hose clamps for 2"id pipes (19)
Pep Boys
$19 ($2 for 2 pack)
Hose clamps for 2.5"id pipes (8)
Pep Boys
$8 ($2 for 2 pack)
Compressor Bypass Valve (BOV):
'90 Plymouth Laser compressor bypass valve
Junkyard
$30
1" id steel pipe section
Home Depot
$3
1 ft. 1" id radiator 45 degree bend hose
Napa
$12
Hose clamps for 1"id pipe (2)
Pep Boys
$2 ($2 for 2 pack)
Downpipe:
2.5"id flex section 6"length
Hileri Dist.
$55
2.5"id 3 bolt exhaust flange
JC Whitney $2
2.5"id 3 bolt aluminum gasket
Pep Boys
$15
Labor & 2.5" piping
Ross Mufflers $100
Oil Lines:
3/8NPT x 5/8 hose heater fitting
Pep Boys
$4
5/8"id high temp rubber hose 1'
Pegasus Racing
$8
Heat reflective tape
Summit Racing
$15
3/8 NPT Tap
Ace Hardware
$8
37/64 Drill Bit
Bisco Tools
$15
1/8 NPT brass tee
Pep Boys
$2
1/8 BSPT -1/8 NPT - 1/8 BSPT tee
McMaster-Carr
$5
-4 AN to 1/8 NPT adapter
Summit Racing
$2
1/8 NPT 1" pipe segment
Pep Boys
$2
4 qts. dino oil (to flush engine)
Pep Boys
$5
4 qts. Synthetic oil
Pep Boys
$18
Water Lines:
3/8"id rubber hose 4' x 2
Pep Boys $4
5/8-3/8-5/8 heater hose tees x2
Pep Boys $6
3/8" hose clamps (6)
Pep Boys $6
(2$ for 2 pack)
5/8" hose clamps (4)
Pep Boys $4
($2 for 2 pack)
Water Wetter
Pep Boys $8
Antifreeze
Pep Boys $6
Beer:
Celis, Irish Stout, Busch
HEB Grocery ,
homebrew
$??? varies with mood
Miscellaneous:
Assorted nuts & bolts, sheet metal stock,
Ultra-grey RTV, zip ties, teflon paste, WD-40, carb cleaner,
fuel inj. washers, copper exh. manifold gasket,
JB Weld, etc.
Purchased from Pep Boys, Home Depot,
Summit, & (very cool).
$??? depends on what you need
Roughly this project cost me $2400 not including
a few tools I had to buy along the way. I also need
a heavy duty clutch now (suprise!) but didn't
include that in the total, it'll run ~$300.
