Since much of the work I do involves overhauling
grandfather clocks, problems relating to their designs and
performance have been part of the challenge. The plot
thickens with modern mechanisms because they are
mass-produced in prodigious quantities, made possible by
newer methods of production and choice of raw materials
that facilitate time-saving and cost-cutting techniques
essential to mass production and the long-term reduction in
costs to the consumers. While these techniques are truly
effective in cutting costs, they frequently compromise the
overall quality and durability of the products.
One technique frequently used by manufacturers is to use
the same grandfather clock weights for several different mechanisms, making
it possible to order larger quantities of particular sizes,
thereby benefiting from economies of scale and lower cost
per unit. I have seen many clocks made since the 1960’s
that have weights that are far too heavy. For example, I
have a German clock with a Kieninger movement (one
second pendulum, Westminster chime, chain driven, ca
1968) with a 9 pound time weight, giving the pendulum
extraordinary overswing.
Antique clocks, while frequently equipped with heavier
weights than necessary, have movements that were less
precisely engineered than the modern, machine-made
‘technowunders’, which makes them more forgiving to
work on. For example, the antique British grandfather
clocks (circa 1830) with recoil escapements frequently have 14 or even 17 pound time weights, yet they may work well with 8 pounds, or even 6 pounds.
I began collecting data by recording information about the
mechanisms that came in for repair and weighing the
weights that came with them. After overhauling them, I
would observe and compare them. The most common
observation was that many chain-driven clocks were severely
overpowered because the manufacturers of the clock
cases used the same weights for the chain-driven clocks
as they did for the cable-driven clocks. All else being equal,
the cable-driven clock needs twice the weight, so these
chain-driven clocks probably had twice as much weight as
they should have been equipped with! It is almost as if the manufacturers had simply reached for whatever weights happened to be on the shelf (in inventory).
While I collected data for all weights, I have not yet found it
necessary to question a manufacturer’s choice of chime or
strike weight, only the time weight. Collecting data for all
weights, however, enabled me to compare different clocks
and to look for patterns in the data. In general, 9 pounds
is far too heavy for a clock like the abovementioned Kieninger, especially for a Graham escapement. The
same clock would run well with 5 to 6 pounds. Hermle
recommends 4.5 pounds for their grandmother movements
(451), and I have seen many equipped with 6 pounds. A clock is certainly more likely to run better if it has some excess power, but it will wear more and will probably continue to run long after the lubricant has failed, simply grinding away.
After collecting data from about fifty clocks, I began to
compare the results and to study their escapements to see if
I could draw some conclusions. In general, for example, I
feel that a Recoil escapement should have about 50% more power
(weight) than if the same clock had a Graham escapement. A
clock with a big and heavy lyre pendulum may need 20 to
30% more weight than the same clock with a light and
simple wooden stick pendulum of the same length. A clock
with very narrow swing of pendulum will require
considerably less weight that one with a very wide swing:
whereas my Hermle grandmother movement would run
well with 4.5 pounds, my Kieninger grandfather movement
needs about six pounds because the latter has a much wider
pendulum swing. I am suggesting that different clock
designs should have different weight requirements, yet
most of the data I have collected suggest a clear pattern of
using certain weight sizes for a wide variety of different clocks. The benefits for mass production can cause problems at the bench, particularly since most repairers are likely to believe that the weight that came with the clock must unquestionably be correct. However, many may not have
thought that the manufacturers of the cases would even
consider using weights other than those specified by the
manufacturers of the mechanisms (assuming that the specifications provided by the manufacturers of the mechanisms were correct?).
I suggest that the repairer should collect data to determine
when it may be necessary to change the weight. While this
is not necessary very often, the repairer would be providing
a better service to the customer if the repairer knew when
the manufacturer of the clock cabinet had provided weights
that are too heavy or not heavy enough. The weights
provided are usually moderately overpowered, say by 20%,
which is acceptable and should not be changed. However,
if I see a 9 pound weight on a clock that I know would run
well with 6 pounds, I would change it, particularly if I had
collected enough data to support this conclusion.
A few clocks come in for repair with weights that are not
heavy enough. If the clock ran for ten years with that
weight, that weight must surely be enough. The customer
said it ran for ten years, yet it does not have a lot of wear
that you can see: sometimes the information given to the
repairer is intended to minimize the problem so that the
estimate of the repair costs would be lower. The repairer
must base his decisions on past experience working with
other similar clocks of similar age. If the pendulum has no
visible overswing after it is overhauled, then it has just
barely enough weight to keep it going: the overswing
should be small but visible during the test run. If the
overswing were very large, the weight should be changed
for a smaller one. If there were no visible overswing, the
weight should be increased by a small amount (by 10 to
20%).
When collecting information, you want to record the year,
make and model of the movement, type of escapement,
number of chimes, chain or cable driven, and the distance
the weights travel down over seven days (P.E.=mgh). If the clock has a second hand with several additional gears in the time train
and a friction spring, the time weight should be heavier
than for the same clock without a second hand, so this is an
important feature to record. Another important feature to
record is whether the escapement has a self-adjusting beat
incorporated into its design because the design of the
pallets is compromised in order to achieve this (the pallet’s
impulse face angles are less than 45º relative to the
impulse provided by the escape wheel, so the efficiency of
the power transfer is less than without the compromise). A
self-adjusting beat design would require more weight than an
optimally-designed Graham escapement.
I would like to discuss two modern clocks, for which I have
found it necessary to increase the time weight because,
even if the clock runs with the weight provided, it is just
barely running. A small increase in weight would reduce
the chances of the repairer getting a come-back and yet
would not cause a large increase in wear, thereby enabling
the repairer to provide the customer with a higher level of
service.
Hermle grandfather movement (e.g.. 1161-853), triple
chime, cable driven.
Some of these clocks have second hands, some do not. If it
has a second hand and the time weight weighs 8 to 8.5
pounds, check the pendulum swing carefully. I have seen
many that had no visible overswing. Increasing the weight
by 16 to 24 ounces solves this problem and provides a
small amount of visible overswing. The same clock without
a second hand is less likely to need added weight. It
appears that both models are equipped with the same
weight. Newer Hermles with the new self-adjusting beat
design should be watched particularly carefully.
Urgos grandmother and grandfather movements (‘03’, ‘32’,
and ‘66’), Westminster chime or triple chime, cable driven.
These clocks have self-adjusting beat, Graham-style
escapements with escape wheels that have very small teeth.
This design is very unforgiving in that it is either correctly
adjusted or it is incorrect (the parameters of adjustment are
very limited). The pallet impulse face angles are
considerably less than 45º, rendering the efficiency
of power transfer very low. In addition, the weights travel
down slowly over seven days, less distance than for most
other cable-driven clocks. Yet these clocks are equipped
with 8 pound weights for the time train. Some of these
clocks have second hands with four extra gears in the time
train and a friction spring. With 8 pounds there is no visible
overswing, so increasing the weight is necessary. However,
the small escape wheel teeth do not allow for as much
overswing as other escape wheel designs, so the repairer
must be cautious because 9.5 to 10 pounds are too much. If
you overhaul one of these clocks and see no visible
overswing, increase the time weight to 9 pounds and
observe the pendulum. These escapements are difficult and
unforgiving, but there are too many grandfather clocks out
there with these mechanisms for repairers to avoid working
on them!
To see some examples of weight specifications, particularly grandfather clock weights, provided by the manufacturers of the mechanisms, go to the website of a clock movement supplier: click here to see HERMLE WEIGHTS and to see URGOS AND KININGER WEIGHTS (If the charts on the website of the clock supplier are not available, select This Link). Looking at the data, you can see that for the Hermle 1161 grandfather clock weights, 5.7 pounds for the chain-driven version would be equivalent to 11.4 pounds for the cable-driven version, yet the chart recommends only 7.7 pounds for the cable-driven version. I think 7 pounds for the either version would be good for the time train, even if it has a second hand. The same information is true for the Hermle 461. As a second example, consider the Urgos chart, in which the UW030 with a lyre pendulum should have a 9.5 pound weight if it is chain driven, yet the chart says it should have an 8.5 pound weight if it is cable driven. However, if you see a UW66 cable-driven clock with a 4 pound time weight, you would probably have difficulty keeping it running. The information in those charts were provided by the manufacturers of the mechanisms. If the manufacturers of the grandfather clock cases used whatever weights happened to be on the shelf, and the manufacturers of the mechanisms provided inconsistent and even questionable weight specification information, then the repairman could not assume that the weights that came with the clock were correct.
To conclude, a word of caution: be sure that every aspect of
the repair and adjustment of the mechanism has been
correctly performed before you consider changing modern grandfather clock weights. Solve all other problems first! Please do not increase the weight to avoid repairing a clock properly,
replacing bushings, polishing pivots, repairing and
adjusting the escapement, etc. Doing so would make a
badly worn clock worse. While determining the correct
weight to use is not a precise science, you need to collect
data before you consider making changes because you are
making an ‘educated guess’.
Update 2015: Mainsprings in American Clocks (has a section about weights).