Shroomry
Queen Marjuana
Shrooms
Mary Jane
Growing Tips
Games
Big Birtha
WHAT YOU'LL NEED: Strong Lungs One of those big bottle from a Water Cooler (stolen preferably)
An VERY LONG aluminum or brass stem threaded on one end.
A big party bowl that matches the threads on the stem.
A rubber stopper to put in the top with a hole to put the stem through.
A drillbit the width of the plastic tubing.
2 to 10 feet of clear tubing (get at a place that has stuff for aquariums like a pet store).
Clear silicone caulk. Drill two holes to fit the clear tubing. Attach hoses. (NOTE: attach as many as you want!) Seal with caulk -let dry overnight.
Stick stem through rubber stopper. Fill with water. Place stopper in top. Attach bowl. Destroy lungs!
THE CHEAP BONG 2
This bong is designed so you don't get a mouthful of water
WHAT YOU'LL NEED (this should be around the house):
A 12 oz. Plastic Soda bottle
A ballpoint Pen (Bic type- hollow tube)
Alot of Aluminum Foil
A needle (or toothpick)
Used Chewing Gum
Take the Soda bottle. Use pen to make hole in side a 1/3 up from the bottom. remove pen guts (so there is a hollow tube). Push into bottle and seal with chewing gum. Take aluminum foil and form bowl with a hollow stem at least 2 inches long (you want to make sure theat doesn't melt the plastic pen tube - plastic fumes can kill you, or at least make you VERY sick. Use the pen to wrap the foil around - that will make sure you can pull air through it. Fill with water so that bottom of pen tube is below water. You now own the cheapest bong known to mankind! NOTE: Beware of lighting your hair on fire when you light this thing!
THE DUEL BONG
The smoothest bong ever.
WHAT YOU'LL NEED:
A half a foot, and a foot long piece of clear
plexiglass pipe, about 3 inches in diameter.
A base to put the cylinders on.
An aluminum or brass stem threaded on one end.
A bowl that matches the threads on the stem A drill with a drill bit as big as the stem and a
1/4 inch drillbit (for making the carb hole)
A drillbit the width of the plastic tubing.
A piece of plastic tubing between a 1/4 and a 1/2 inch thick
A plastic cap to cover the first cylinder tightly (needs to form a seal)
Clear silicone caulk.
Attach hose through the top of the cap into the first cylinder (IMPORTANT: hose end should be ABOVE the water line). The other end of the hose, which goes in the second cylinde,r should be submerged unde the water. Make sure the cap on the first cylinder forms a very tight seal! HOW IT WORKS: Load the first chamber boiling water and the second chamber with ice water. Use normally, like a standard cylinder bong.
THE WELFARE HOOKAH
A basic hookah if you don't feel like spending over fifty or more for one of those glass jobs.
Easily made and you can also just put on one hose for personal use.
WHAT YOU'LL NEED:
An empty 2 liter soda bottle
3 to 5 feet of clear tubing (get at a place that has stuff for aquariums like a pet store).
A bowl attached to a long stem.
A knife or something similar to cut the holes in the plastic bottle (not so easy)
Clear silicone caulk.
HOW IT WORKS:
Assemble via the blueprint, then light up and draw through the hoses. Not as afficient as the expensive kind but it works. Now you can act like turban-wearing Opium lord. A good project for a rainy afternoon.
THE DIRTWEED BONG (aka the BBQ BONG)
WHAT YOU'LL NEED:
A Weber BBQ (the hibachi-like one).
3 inch diameter clear plexiglass tube. Heat resistant epoxy.
A drill with a drill bit to open 3 inch hole on lid of weber grill.
A minimum of a 1/4 pound of dirct weed.
HOW IT WORKS:
After dinner, when the coals are hot, toss a 1/4 of crappy weed on the grill and close tight. Inhale at will. Your friends and you will likely be found dead the next morning.
THE STANDARD CYLINDER MODEL
This is a simple one. Basic, works great, and is easy to use!
WHAT YOU'LL NEED:
2 feet of clear plexiglass pipe, about 3 inches in diameter.
An aluminum or brass stem threaded on one end.
A bowl that matches the threads on the stem
A drill with a drill bit as big as the stem and a 1/4 inch drillbit (for making the carb hole)
Clear silicone caulk.
HOW IT WORKS:
We think you can figure it out.
THE DEATH BONG
A brutal design. Will even make the most basic cannibas very strong. Be careful!
WHAT YOU'LL NEED:
1 foot and 2 feet pieces of plexiglass pipe, about 3 inches in diameter. You will have to make a "Y" shape splitting off from the main pipe at a 45° angle. You will need plastic epoxy!
An aluminum or brass stem threade on one end (the thread to the valve has to attach to the stem).
A threaded brass valve that closes in half a turn.
A bowl that matches the threads on the valve.
A drill with a drill bit as big as the stem.
A cap from an aerosol can that will fit in the end of the short Y off the main pipe, just tight enough to close it off.
One foot of rope or bungee cord.
Silicone caulk
HOW IT WORKS:
Not quite as simple as a standard bong. The carbeurator is the big pipe splitting off at 45°. This allows a LARGE amount of smoke to blast into your lungs VERY suddenly! The process is like this.
1. Light up.
2. Start smoking.
3. Close the valve (this cuts off all incoming air).
4. YANK the cord attached to the plastic aerosol top. This causes a ton of smoke to go into your lungs instantly.
5. Pass out.
The Coke Can Pipe
This is a very Cheap :-) and pretty good to use
What You will need
1.A coke can
2.a knife or pen
3.and of course herbal refreshments
How it works and how you make it
You crush the can so it is flat on top of it and poke little holes on top of the can.Then poke a big hole in the back of the can this is the carborater. You put the Herbs on top of the can where you poked all the little holes and put your thumb over the carborater and light up and start smokeing!!! :-> I will be Makeing this TEN TImEs better but this does the JoB :-).
E
N
J
O
Y
